IL36A/IL1F6 ELISA Kit

Produktnummer ABIN6974803

Produktdetails IL36A/IL1F6 ELISA Kit

Target: IL36A/IL1F6 (IL1F6) (Interleukin 1 Family, Member 6 (IL1F6))

Reaktivität: Human

Nachweismethode: Colorimetric

Methodentyp: Sandwich ELISA

Detektionsbereich: 15.6 pg/mL - 1000 pg/mL

Untere Nachweisgrenze: 15.6 pg/mL

Applikation: ELISA

Verwendungszweck: For the quantitative determination of human interleukin-36 alpha (IL1F6) concentrations in serum, plasma, tissue homogenates, cell culture supernates.

Proben: Cell Culture Supernatant, Plasma, Serum, Tissue Homogenate

Analytische Methode: Quantitative

Spezifität: This assay has high sensitivity and excellent specificity for detection of human IL1F6. No significant cross-reactivity or interference between human IL1F6 and analogues was observed. Note: Limited by current skills and knowledge, it is impossible for us to complete the cross-reactivity detection between human IL1F6 and all the analogues, therefore, cross reaction may still exist.

Sensitivität: 3.9 pg/mL

Bestandteile:

• Assay plate
• Standard
• HRP-avidin (100 x concentrate)
• Biotin-antibody (100 x concentrate)
• Sample Diluent
• HRP-avidin Diluent
• Biotin-antibody Diluent
• Wash Buffer (25 x concentrate)
• TMB Substrate
• Stop Solution
• Adhesive Strip

Anwendungsinformationen

Applikationshinweise: Optimal working dilution should be determined by the investigator.

Probenmenge: 100 μL

Testdauer: 1 - 4.5 h

Plattentyp: Pre-coated

Protokoll:

1. Prepare reagents, samples and standards as instructed.
2. Add 100 µL standard or sample to each well. Incubate 2 hours at 37 °C.
3. Remove the liquid of each well, don't wash.
4. Add 100 µL Biotin-antibody (1x) to each well. Incubate 1 hour at 37 °C.
5. Aspirate and wash 3 times.
6. Add 100 µL HRP-avidin (1x) to each well. Incubate 1 hour at 37 °C
7. Aspirate and wash 5 times.
8. Add 90 μL of TMB Substrate to each well. Incubate for 15-30 minutes at 37 °C. Protect from light.
9. Add 50 µL Stop Solution to each well. Read at 450 nm within 5 minutes.

Aufbereitung der Reagenzien:

1. Biotin-antibody (1x) - Centrifuge the vial before opening. Biotin-antibody requires a 100-fold dilution. A suggested 100-fold dilution is 10 μL of Biotin-antibody + 990 μL of Biotin-antibody Diluent.
2. HRP-avidin (1x) - Centrifuge the vial before opening. HRP-avidin requires a 100-fold dilution. A suggested 100-fold dilution is 10 μL of HRP-avidin + 990 μL of HRP-avidin Diluent.
3. Wash Buffer (1x) - If crystals have formed in the concentrate, warm up to room temperature and mix gently until the crystals have completely dissolved. Dilute 20 mL of Wash Buffer Concentrate (25 x) into deionized or distilled water to prepare 500 mL of Wash Buffer (1 x).
4. Standard Centrifuge the standard vial at 6000-10000rpm for 30s. Reconstitute the Standard with 1.0 mL of Sample Diluent. Do not substitute other diluents. This reconstitution produces a stock solution of 1000 pg/mL. Mix the standard to ensure complete reconstitution and allow the standard to sit for a minimum of 15 minutes with gentle agitation prior to making dilutions. Pipette 250 μL of Sample Diluent into each tube (S0-S6). Use the stock solution to produce a 2-fold dilution series (below). Mix each tube thoroughly before the next transfer. The undiluted Standard serves as the high standard (1000 pg/mL). Sample Diluent serves as the zero standard (0 pg/mL).

Note:

• Kindly use graduated containers to prepare the reagent. Please don't prepare the reagent directly in the Diluent vials provided in the kit.
• Bring all reagents to room temperature (18-25 °C) before use for 30 min.
• Prepare fresh standard for each assay. Use within 4 hours and discard after use.
• Making serial dilution in the wells directly is not permitted.
• Please carefully reconstitute Standards according to the instruction, and avoid foaming and mix gently until the crystals have completely dissolved. To minimize imprecision caused by pipetting, use small volumes and ensure that pipettors are calibrated. It is recommended to suck more than 10 μL for once pipetting.
• Distilled water is recommended to be used to make the preparation for reagents. Contaminated water or container for reagent preparation will influence the detection result.

Aufbereitung der Proben:

• It is recommended to use fresh samples without long storage, otherwise protein degradation and denaturationmay occur in these samples, leading to false results. Samples should therefore be stored for a short periodat 2 - 8 °C or aliquoted at -20 °C (≤1 month) or -80 °C (≤ 3 months). Repeated freeze-thawcycles should be avoided. Prior to assay, the frozen samples should be slowly thawed and centrifuged toremove precipitates.
• If the sample type is not specified in the instructions, a preliminary test is necessary to determinecompatibility with the kit.
• If a lysis buffer is used to prepare tissue homogenates or cell culture supernatant, there is a possibilityof causing a deviation due to the introduced chemical substance.The recommended dilution factor is for reference only.
• Please estimate the concentration of the samples before performing the test. If the values are not in therange of the standard curve, the optimal sample dilution for the particular experiment has to be determined.Samples should then be diluted with PBS (pH =7.0-7.2).

Testpräzision: Intra-assay Precision (Precision within an assay): CV%<8% Three samples of known concentration were tested twenty times on one plate to assess.
Inter-assay Precision (Precision between assays): CV%<10% Three samples of known concentration were tested in twenty assays to assess.

Beschränkungen: Nur für Forschungszwecke einsetzbar

Handhabung

Lagerung: 4 °C,-20 °C

Informationen zur Lagerung: Unopened kit Store at 2 - 8°C. Do not use the kit beyond the expiration date May be stored for up to 1 month at 2 - 8°C. Coated assay Try to keep it in a sealed aluminum foil bag, plate and avoid the damp. Standard May be stored for up to 1 month at 2 - 8° C. If Biotin-antibody don't make recent use, better keep it store at HRP-avidin -20°C. Biotin-antibody Diluent Opened kit HRP-avidin Diluent Sample May be stored for up to 1 month at 2 - 8°C. Diluent Wash Buffer TMB Substrate Stop Solution *Provided this is within the expiration date of the kit.

Haltbarkeit: 6 months

Referenzen für IL36A/IL1F6 ELISA Kit (ABIN6974803)

Ciccia, Accardo-Palumbo, Alessandro, Alessandri, Priori, Guggino, Raimondo, Carubbi, Valesini, Giacomelli, Rizzo, Triolo: "Interleukin-36? axis is modulated in patients with primary Sjögren's syndrome." in: Clinical and experimental immunology, Vol. 181, Issue 2, pp. 230-8, (2015) (PubMed).

Shi, Sun, Li, Zhao, Ju, Mu, Yan, Li, Zeng, Lu: "A Combination of Targeted Sunitinib Liposomes and Targeted Vinorelbine Liposomes for Treating Invasive Breast Cancer." in: Journal of biomedical nanotechnology, Vol. 11, Issue 9, pp. 1568-82, (2015) (PubMed).

Details zu IL36A/IL1F6

Target: IL36A/IL1F6 (IL1F6) (Interleukin 1 Family, Member 6 (IL1F6))

Andere Bezeichnung: interleukin 1 family, member 6 (epsilon) (IL1F6 Produkte)

Synonyme: Il1f6 ELISA Kit, Fil1 ELISA Kit, IL-1H1 ELISA Kit, IL1RP2 ELISA Kit, Il1f9 ELISA Kit, Il36a ELISA Kit, FIL1 ELISA Kit, FIL1(EPSILON) ELISA Kit, FIL1E ELISA Kit, IL-1F6 ELISA Kit, IL1(EPSILON) ELISA Kit, IL1F6 ELISA Kit, interleukin 36, alpha ELISA Kit, interleukin 1 family, member 6 (epsilon) ELISA Kit, interleukin 1 family, member 6 ELISA Kit, interleukin 36 alpha ELISA Kit, Il36a ELISA Kit, IL1F6 ELISA Kit, IL36A ELISA Kit, Il1f6 ELISA Kit

Hintergrund:

Abbreviation: IL36A

Alias: FIL1, FIL1(EPSILON), FIL1E, IL-1F6, IL1(EPSILON), MGC129552, MGC129553, IL-1F6 (FIL-1-epsilon)|interleukin 1, epsilon

UniProt: Q9UHA7

Pathways: Cancer Immune Checkpoints